← Back to Peerless - 6½" SDS Mid-Woofer - 830657
Where the figures for 830657 come from
I take every figure from Peerless' own product page or datasheet where I can. This lists where each figure on the 830657 page came from.
- 29 from Peerless' product page
- 3 from Peerless' datasheet
- 3 worked out from Peerless' figures
- 1 my estimate
- 1 not yet checked
- 4 from NB Audio's listing
General
| Driver type | Mid-Woofer | NB Audio's listing |
|---|---|---|
| Nominal size | 6.5" | NB Audio's listing |
| Nominal impedance | 8Ω | Maker's product page |
| Series | Peerless Subwoofer | NB Audio's listing |
| Power handling (RMS) | 60 W | Maker's product page |
| Sensitivity | 89 dB | Maker's product page |
| Suggested alignment | Either | NB Audio's listing |
Thiele/Small parameters
| Resonant frequency (Fs) | 48 Hz | Maker's product page |
|---|---|---|
| DC resistance (Re) | 5.9 Ω | Maker's product page |
| Minimum impedance (Zmin) | 6.4 Ω | Maker's product page |
| Voice coil inductance (Le) | 0.591 mH | Maker's product page |
| Mechanical Q (Qms) | 2.67 | Maker's product page |
| Electrical Q (Qes) | 0.565 | Maker's product page |
| Total Q (Qts) | 0.47 | Maker's product page |
| Equivalent volume (Vas) | 20.1 L | Maker's product page |
| Compliance (Cms) | 0.72 mm/N | Maker's product page |
| Moving mass (Mms) | 15.4 g | Maker's product page |
| Mechanical resistance (Rms) | 1.74 kg/s | Worked out from the maker's figures |
| Force factor (Bl) | 6.92 T·m | Maker's product page |
| Effective piston area (Sd) | 141 cm² | Maker's product page |
| Linear excursion (Xmax, one-way) | 5.46 mm | Maker's product page |
| Mechanical excursion (Xmech) | 10 mm | Maker's product page |
| Displacement volume (Vd) | 76.99 cm³ | Worked out from the maker's figures |
| Efficiency bandwidth product (EBP) | 84.96 | Worked out from the maker's figures |
Motor
| Motor efficiency factor (β) | 8.19 (T·m)²/Ω | Maker's product page |
|---|---|---|
| Air gap height | 6 mm | Maker's product page |
| Voice coil winding height | 12.9 mm | Maker's product page |
| Voice coil layers | 2 | Maker's product page |
| Voice coil wire | CU | Maker's product page |
| Magnet size (OD × ID × thickness) | 81 × 32.5 × 15 mm | Maker's product page |
Mounting
| Overall diameter | 182 mm | My earlier listing, not yet checked |
|---|---|---|
| Faceplate | Round with two flats, Ø182 mm, 164 mm across the flats | Maker's datasheet |
| Cutout diameter (suggested) | ≈ 145.0 mm | My estimate, from the maker's drawing |
| Mounting depth | 72.1 mm | Maker's datasheet |
| Flange thickness | 3 mm | Maker's datasheet |
| Voice coil diameter | 25.7 mm | Maker's product page |
| Weight | 0.84 kg | Maker's product page |
Materials
| Cone | Coated Paper | Maker's product page |
|---|---|---|
| Surround | SBR | Maker's product page |
| Basket | Steel | Maker's product page |
| Magnet | Ferrite | Maker's product page |
Not on file: Bolt circle. Either the maker doesn't publish it or I haven't found it yet.
What the labels mean
- Maker's product page: copied from the maker's product page.
- Maker's datasheet: read off the maker's own datasheet or drawing.
- Worked out from the maker's figures: Vd = Sd × Xmax, EBP = Fs ÷ Qes.
- My estimate, from the maker's drawing: measured off the maker's drawing, usually within ±0.3 mm (up to ±0.5). The suggested cutout is the basket's width on the drawing plus 1 mm of clearance (1.5 mm on drivers over 200 mm). Measure before you cut.
- My earlier listing, not yet checked: from the listing I had before I started checking figures against makers. Treat it as a guide until it's checked.
- NB Audio's listing: how I've filed it in the store.
Check them yourself: Spec Sheet