← Back to SB Acoustics - 3" PGC Full Range - SB10PGC21-4
Where the figures for SB10PGC21-4 come from
I take every figure from SB Acoustics' own product page or datasheet where I can. This lists where each figure on the SB10PGC21-4 page came from.
- 24 from SB Acoustics' product page
- 3 from SB Acoustics' datasheet
- 2 worked out from SB Acoustics' figures
- 1 my estimate
- 1 not yet checked
- 3 from NB Audio's listing
General
| Driver type | Full Range | NB Audio's listing |
|---|---|---|
| Nominal size | 3" | NB Audio's listing |
| Nominal impedance | 4Ω | Maker's product page |
| Power handling (RMS) | 20 W | Maker's product page |
| Sensitivity | 84 dB | Maker's product page |
| Frequency range | 90 – 20,000 Hz | Maker's product page |
| Suggested alignment | Either | NB Audio's listing |
Thiele/Small parameters
| Resonant frequency (Fs) | 89 Hz | Maker's product page |
|---|---|---|
| DC resistance (Re) | 3.4 Ω | Maker's product page |
| Voice coil inductance (Le) | 0.15 mH | Maker's product page |
| Mechanical Q (Qms) | 11.2 | Maker's product page |
| Electrical Q (Qes) | 1.01 | Maker's product page |
| Total Q (Qts) | 0.92 | Maker's product page |
| Equivalent volume (Vas) | 1.2 L | Maker's product page |
| Compliance (Cms) | 1.14 mm/N | Maker's product page |
| Moving mass (Mms) | 2.8 g | Maker's product page |
| Mechanical resistance (Rms) | 0.14 kg/s | Maker's product page |
| Force factor (Bl) | 2.3 T·m | Maker's product page |
| Effective piston area (Sd) | 27 cm² | Maker's product page |
| Linear excursion (Xmax, one-way) | 2.25 mm | Maker's product page |
| Displacement volume (Vd) | 6.075 cm³ | Worked out from the maker's figures |
| Efficiency bandwidth product (EBP) | 88.12 | Worked out from the maker's figures |
Motor
| Voice coil height | 7.5 mm | Maker's product page |
|---|---|---|
| Air gap height | 3 mm | Maker's product page |
| Magnetic flux density | 0.8 T | Maker's product page |
| Magnet weight | 0.09 kg | Maker's product page |
Mounting
| Overall diameter | 95.5 mm | Maker's datasheet |
|---|---|---|
| Faceplate | Not round (see the maker's drawing) | Maker's datasheet |
| Cutout diameter (suggested) | ≈ 74.6 mm | My estimate, from the maker's drawing |
| Mounting depth | 44.2 mm | Maker's datasheet |
| Voice coil diameter | 20.4 mm | Maker's product page |
| Weight | 0.24 kg | Maker's product page |
| Width | 77.4 mm | My earlier listing, not yet checked |
Materials
| Cone | Fibreglass | Maker's product page |
|---|
Not on file: Bolt circle, Flange thickness. Either the maker doesn't publish it or I haven't found it yet.
What the labels mean
- Maker's product page: copied from the maker's product page.
- Maker's datasheet: read off the maker's own datasheet or drawing.
- Worked out from the maker's figures: Vd = Sd × Xmax, EBP = Fs ÷ Qes.
- My estimate, from the maker's drawing: measured off the maker's drawing, usually within ±0.3 mm (up to ±0.5). The suggested cutout is the basket's width on the drawing plus 1 mm of clearance (1.5 mm on drivers over 200 mm). Measure before you cut.
- My earlier listing, not yet checked: from the listing I had before I started checking figures against makers. Treat it as a guide until it's checked.
- NB Audio's listing: how I've filed it in the store.
Check them yourself: 3″ SB10PGC21-4 Datasheet